Industrial Blade Terminology: 134 Terms Buyers Actually Use

One part has three names, one steel has four designations. This is the vocabulary we actually use when specifying industrial blades — defined at the machine, not in a metallurgy textbook.

  • 39Blade type
    terms
  • 27Edge & tooth
    terms
  • 30Material
    terms
  • 38Dimension & wear
    terms

Technical reference

Every blade enquiry runs into the same problem: the same part has three names, and the same steel has four designations. This glossary collects the terms we actually use when specifying industrial blades — what each one means, why it matters at the machine, and which of our blade ranges it refers to.

It is written for buyers, maintenance engineers and sourcing teams rather than for metallurgists. If a term you need is missing, send it over and we will add it.

134 terms across five groups · updated November 2026 · Dekeer technical team

Blade Type Terms

The names buyers actually use on the shop floor, grouped by what the blade does rather than by what it is called in a catalogue. One machine often needs several of these at once.

Packaging Machine Blade

Any blade that sits in the sealing, cutting, notching or slitting station of a form-fill-seal line. The same machine usually carries several: one seals the film, one cuts the pack off, one punches the easy-open notch. Because each station loads the blade differently, they are specified separately even when they share a jaw holder. See packaging machine blades we manufacture.

Also called: packaging knife, packaging cutter blade

Serrated Blade

A blade whose cutting edge carries a continuous row of teeth instead of a straight line. The teeth concentrate pressure on a small contact area, which lets the edge bite into slippery film, foil or fibre that a plain edge would skate over. Tooth pitch and depth decide whether the blade seals, tears or separates the material. See serrated industrial knives.

Also called: toothed blade, jagged-edge blade

Serrated Sealing Knife

The blade mounted in the sealing jaw of a VFFS or HFFS machine. It presses the film against the anvil and welds it in one stroke, so the tooth pattern has two jobs at once: form a crimp that holds pressure along the seal, and leave enough interruption that the finished pack can be torn apart at the perforation line. See packaging blade guide.

Also called: crimp knife, sealing jaw blade

Cut-Off Blade

The blade beside the sealing jaw that separates the finished pack from the web. On most lines it is a straight or lightly serrated edge running against a hardened anvil; on high-speed lines it becomes a rotary disc or a flying knife so the web never has to stop. See cut-off blade options.

Usually specified together with the sealing jaw

Tear Notch Punch

A small punch that cuts a V or U shaped notch into the seal area so the consumer can start a tear in a controlled direction. Depth is measured from the seal edge, and the V angle plus its position relative to the bag centre line decide whether the pack opens along the seal or rips through the print. See notching and punching blades.

Also called: easy-open notch punch, tear-start punch

Perforating Blade

A blade that cuts a row of small holes or a line of interrupted slits rather than a continuous cut. Used to vent coffee and produce packs, to create a controlled tear line on multi-packs, and to weaken a web so it separates cleanly downstream. Hole size, pitch and pattern are held constant along the whole blade. See perforating blades on packaging lines.

Also called: micro-perforating blade, pin-perforating blade

Slitting Blade

A blade that cuts a running web into narrower strips along its length. Slitting is a shear operation: the blade and its counter-edge pass each other with a defined overlap so the material is cut rather than crushed. The same word covers rotary discs, razor blades and score-cut wheels. See circular slitting blades we manufacture.

See also: top knife, bottom knife, clearance

Circular Slitter Blade

A disc-shaped blade with a central bore, used in pairs or against a hardened sleeve to slit film, foil, paper, tape or metal coil. Diameter, thickness, bore and edge angle are all set by the material and the line speed; a blade that is correct for 12 micron PET is wrong for 0.5 mm aluminium. See longitudinal shear circular blades.

Also called: slitter disc, rotary slitting knife

Top Knife and Bottom Knife

The two halves of a shear-slitting pair. The top knife is the driven disc that enters the material; the bottom knife is the counter-edge it shears against. Their side clearance and vertical overlap decide cut quality far more than sharpness alone, which is why both are usually replaced or reground as a set. See slitter clearance and overlap chart.

Also called: male and female knife, upper and lower slitter

Score Slitter Blade

A slitting blade that presses through the material against a hardened roll instead of shearing against a counter-blade. It produces a clean edge on thin films and foils with very little dust, but it needs higher pressure and a hard anvil roll, so it is not used on thick or abrasive stock. See score and shear slitting options.

Also called: crush-cut blade, pressure slitter

Razor Slitter Blade

A thin, very sharp blade held in a spring-loaded holder that trails or draws through the web. Used where the material is too thin or too sensitive for shear slitting, such as battery separator film, thin tape and light foil. Blade thickness and edge angle matter more than diameter here. See razor slitting blades.

Also called: razor blade slitter, draw slitter

Doctor Blade

A thin steel blade clamped against a rotating cylinder to meter a film of ink, coating or adhesive to a fixed thickness. The blade does not cut: it wipes. Consistency comes from blade flatness, edge straightness and uniform clamping pressure along the whole length, not from hardness. See doctor blades we manufacture.

Also called: metering blade, wiping blade, coating blade

Ink Doctor Blade

The doctor blade in a flexographic or gravure printing unit, metering ink off the anilox or gravure cylinder before it touches the substrate. Print defects such as streaks, ghosting and hazing usually trace back to blade wear, dried ink under the edge or uneven clamp pressure rather than to the ink itself. See ink doctor blade guide.

Also called: printer doctor blade, anilox blade

Coating Blade

A doctor-type blade used to meter adhesive, varnish, paint or battery slurry onto a moving web. Because the metered film thickness is set by the gap between blade edge and substrate, edge straightness and burr-free finishing matter more than a polished face. See doctor blade coating notes.

Also called: applicator blade, metering bar

Granulator Blade

A knife mounted on the rotor or in the bed of a granulator, the machine that reduces plastic scrap, purgings and profiles into regrind. Rotor knives cut against bed knives in a scissor action, so rotor and bed knives are ground and replaced as a matched set or the clearance opens and the cut turns into a crush. See granulator blades and knife sets.

Also called: granulator knife, regrind blade

Bed Knife

The stationary knife in a granulator or chipper that the rotating knives shear against. Bed knives take the impact side of the cut, so they are usually made from tougher stock than the rotor knives and are adjusted to a clearance measured in tenths of a millimetre. See rotor and bed knife sets.

Also called: bed blade, stationary knife, anvil knife

Rotor Knife

A knife bolted into the rotating cutter head of a granulator, shredder or pelletizer. Rotor knives are indexed or reground as a set because a single high knife changes the cutting clearance for every other knife in the head. See rotor knife geometry.

Also called: fly knife, rotating knife

Shredder Blade

A heavy, high-torque blade used for primary size reduction of bulky waste: plastic bales, pallets, tyres, e-waste, metal scrap. Shredder blades are built for impact toughness rather than a fine edge, and are usually reversible so both long edges can be used before regrinding. See shredder and recycling blades.

Also called: shredder knife, tearing blade

Crusher Blade

A blade or fixed tooth in a plastic crusher or hammer-type mill that breaks scrap into small flakes. Unlike a granulator knife, a crusher blade often works by impact and tearing, so edge geometry is blunter and the material choice leans towards toughness. See crusher and granulator blade range.

Also called: crusher knife, breaker blade

Pelletizer Knife

The rotating knife that cuts extruded strands or die-face strands into pellets. Pelletizer knives run in contact with a die face or against a bed knife at high speed, so the blade must hold a sharp edge at temperature without chipping. See custom pelletizer knives.

Also called: pelletizing knife, strand cutter blade

Paper Cutter Blade

The long, straight guillotine blade in a paper cutting machine. It shears a full stack in one stroke, so the critical properties are straightness along the whole length, a consistent bevel and a flat back face that registers against the clamp. See paper cutter blades.

Also called: guillotine blade, paper trimmer knife

Sheeter Knife

A long cross-cut blade on a sheet cutter that converts a paper or board reel into flat sheets. Sheeter knives take repeated impact at line speed, so edge toughness and secure clamping matter as much as sharpness. See sheeter and cross-cut knives.

Also called: cross-cut knife, sheet cutter blade

Core Cutter Blade

A circular or straight blade used to cut paper cores, cardboard tubes and similar wound products to length. Core cutting is a high-pressure operation on an abrasive material, so the edge is usually thicker and more obtuse than a slitting blade. See core cutter blades.

Also called: core cutter knife, tube cutter blade

Woodworking Knife

A cutting knife for planers, moulders, jointers and chippers. Woodworking knives are ground as a set with matched weight and height because an unbalanced or mismatched set causes vibration and a stepped finish on the timber. See woodworking knives.

Also called: planer blade, moulder knife

Jointer Knife

The short knife in a jointer head that squares and flattens the edge of a board before it is glued or profiled. A jointer knife is usually wider in bevel than a planer knife because it takes an interrupted cut across the full board width. See jointer and planer knives.

Also called: jointer blade, surfacing knife

Chipper Knife

A heavy knife in a wood chipper that converts logs, slabs and waste into chips. Chipper knives work by impact and are re-ground frequently; their bevel angle is a compromise between edge life and the energy the machine has to deliver. See chipper knives.

Also called: chipper blade, wood chipper knife

Carton Box Grooving Knife

A profiled knife that cuts the creasing groove in corrugated or solid board so the box folds on a straight line. Grooving removes material rather than shearing it, so the knife profile, width and depth have to match the board grade and the fold radius required. See carton box grooving knives.

Also called: grooving blade, creasing knife, slotting knife

Corrugated Slitter Knife

A slitting blade used on the slitter-scorer of a corrugator to trim and divide board into decks. Corrugated slitting is abrasive and dusty, so these knives wear on the flank rather than the edge and are usually reground to a defined wear land. See corrugated blade guide.

Also called: corrugated slitter, board slitting knife

Corrugated Slotter Blade

A wide, flat blade that cuts the slots and flaps in corrugated board on a flexo folder-gluer. The slotter cuts a full-depth kerf in one pass, so blade thickness, straightness and the condition of the anvil determine whether the slot edge is clean or crushed. See slotting and grooving blades.

Also called: slotter knife, flexo slotter blade

Die Cutting Blade

A steel rule or solid blade formed into the shape of the finished part and pressed through board, film or adhesive. Rotary die cutting uses a blade wrapped around a cylinder, which adds a height tolerance requirement on top of the usual edge geometry. See custom die cutting blades.

Also called: die blade, steel rule die, rotary die

Flying Knife

A cross-cutting knife that travels with the moving web while it cuts, then returns to its start position. Used where the line cannot stop for a cut. Flying knives are balanced rotating assemblies, so a replacement has to match mass and mounting as well as edge geometry. See cross-cutting knife options.

Also called: rotary cross-cut knife, orbital knife

Tungsten Carbide Blade

A blade made from cemented tungsten carbide rather than steel. Carbide holds a sharp edge far longer on abrasive stock such as glass fibre, printed board, filled film and battery electrodes, but it is brittle, so it needs a rigid holder and careful handling. See tungsten carbide blades.

Also called: carbide blade, tungsten blade, TC blade

Stainless Steel Blade

A blade made from a corrosion-resistant grade, typically a martensitic stainless such as 420, 420J2 or 440C that can be hardened. Austenitic grades like 304 and 316 resist corrosion but cannot be hardened, so they are only used where the edge does not have to survive cutting loads. See stainless steel blades.

Also called: inox blade, rust-free blade

Industrial Razor Blade

A thin, single-edge blade used for scoring, trimming, scraping and film cutting. Standardised hole patterns let the same blade fit many holders. Tissue thickness, edge angle and coating decide performance far more than the outline shape. See industrial razor blades.

Also called: utility blade, single-edge blade

Hook Blade

A blade with a hooked point used to cut roofing membrane, carpet, belting and film without damaging the surface underneath. The hook traps the material and pulls it into the edge, so the cut starts from the outside rather than by pressure. See hook blades.

Also called: hook knife blade, roof cutter blade

Trapezoid Blade

A heavy-duty utility blade with a trapezoid outline and two cutting corners. The shape gives a strong point for scoring tough stock and allows the blade to be reversed or advanced in the holder for a fresh corner. See trapezoid blades.

Also called: trapezoid utility blade, heavy-duty blade

Alligator Shear Blade

A blade fitted to the pivoting arm of an alligator shear, used to cut scrap metal, cable and bar. The blade meets a fixed bed knife at an angle, so the cut travels progressively and the edge has to resist impact rather than sliding wear. See shear blades.

Also called: alligator blade, scrap shear blade

Shear Blade

Any blade that cuts by two edges passing each other, as opposed to a blade that presses through the material. Shear blades include guillotine, slitter and alligator types, and all of them depend on correctly set clearance to cut cleanly rather than tear. See shear blades.

Also called: shearing blade, squaring blade

Guillotine Blade

A long straight blade that descends vertically through a stack or sheet. Used for paper, board, film stacks and metal sheet. Because the whole length engages at once, flatness and parallelism across the blade are more critical than on any other blade type. See guillotine and paper cutter blades.

Also called: guillotine knife, straight cutting blade

Edge Geometry and Tooth Profile

The vocabulary of the cutting edge itself. Two blades can be made from the same steel and still behave completely differently, because these are the parameters that decide how a blade bites, seals or tears.

Bevel

The angled face ground on a blade to bring the body thickness down to a cutting edge. Almost every blade characteristic that a buyer can feel, from how it bites to how long it lasts, comes from the bevel rather than from the steel grade.

Also called: grind, facet

Single Bevel

A blade ground on one face only, leaving the other face flat. The flat face registers against a fence or holder, which gives a very straight cut and makes the blade easy to re-sharpen without changing its position. Standard on doctor blades and many woodworking knives.

Also called: one-sided bevel, chisel grind

Double Bevel

A blade ground symmetrically on both faces to a central edge. A double bevel cuts in either direction and is self-centring in the cut, which suits slitting discs, sheeter knives and blades used on reversing machines.

Also called: two-sided bevel, symmetrical grind

Bevel Angle

The angle between the bevel face and the blade face, measured on one side. A shallow angle cuts with less force but has a thin edge that dulls or chips quickly; a steep angle survives impact but needs more machine power. The right value is a function of material hardness and how much impact the cut involves.

Also called: edge angle, grind angle

Included Angle

The total angle at the cutting edge, i.e. both bevels added together. This is the number that actually predicts edge strength, so when a supplier quotes a bevel angle it is worth confirming whether they mean one side or the included angle.

Also called: total edge angle, point angle

Primary and Secondary Bevel

A two-stage grind where a shallow primary bevel does the cutting and a steeper secondary bevel backs it up for strength. The secondary bevel reduces the amount of stock that has to be removed at each regrind, which extends the useful life of the blade body.

Also called: main and relief bevel

Edge Land

A narrow flat left along the cutting edge instead of grinding it to a razor point. A land makes the edge far more resistant to chipping on abrasive or interrupted cuts, at the cost of some sharpness. Corrugated slitters and shredder blades are commonly supplied with a land.

Also called: land width, edge flat

Micro-Bevel

A very small additional bevel applied at the very tip of the edge, usually only a few hundredths of a millimetre wide. It stabilises a thin edge against micro-chipping and is common on carbide and high-hardness blades. It is a deliberate compromise: slightly less initial sharpness for much more predictable wear.

Also called: tip bevel, micro-facet

Edge Radius

The rounding at the very tip of a cutting edge. No production edge is perfectly sharp; a controlled radius is often specified because a perfectly sharp edge breaks down almost immediately in service. Edge radius is measured optically and is a better predictor of performance than nominal sharpness.

Also called: tip radius, hone radius

Straight Edge

A plain continuous cutting edge with no teeth or profile. Straight edges give the cleanest cut and the longest life per regrind, but they have no ability to grip slippery material, which is why packaging lines often replace them with serrated edges. See straight and serrated packaging blades.

Also called: plain edge, smooth edge

Serrated Edge

A cutting edge formed into a continuous row of teeth. Each tooth acts as a small point that concentrates force, so the edge starts a cut in film or fibre that a straight edge would slide across. The trade-off is a slightly ragged cut line and a more complex regrind. See serrated edge options.

Also called: toothed edge, saw edge

Tooth Pitch

The distance from one tooth point to the next, usually quoted in millimetres or as teeth per inch. Fine pitch gives a smoother cut and better seal support; coarse pitch gives deeper penetration and more aggressive grip. Pitch is the single most important number when matching a blade to a film thickness. See serrated tooth pitch.

Also called: tooth spacing, TPI

Tooth Depth

The height of a tooth from root to point. Deeper teeth bite further into the material but leave a weaker seal area, because every tooth root is a gap in the sealing pattern. On sealing jaws, depth and seal width have to be balanced against each other. See serrated blades for packaging.

Also called: tooth height, serration depth

Tooth Profile

The shape of an individual tooth, described by its flank angle, tip form and root radius. A sharp V profile cuts aggressively; a rounded or flat-topped profile is used where the blade has to press and weld rather than sever. Profile is usually shown on a drawing rather than spelled out in words.

Also called: tooth form, serration shape

V-Tooth

A triangular tooth with straight flanks meeting at a sharp point. V-teeth give the most aggressive grip and are common on cut-off and perforating blades. They also concentrate stress at the point, so they chip first on hard or abrasive material.

Also called: triangular tooth, sharp tooth

U-Tooth

A tooth with a rounded root and a blunter tip. U-teeth distribute load over a wider area, which makes them last longer on tough film and reduces the chance of tearing the seal. They are the usual choice for sealing jaws that also have to crimp.

Also called: round tooth, radius tooth

Flat-Top Tooth

A tooth whose tip has been truncated to a small flat. The flat presses and welds without piercing, which is why flat-top profiles appear on combined seal-and-cut jaws and on blades that must not perforate the film.

Also called: truncated tooth, flat crest tooth

Scalloped Edge

A cutting edge formed from shallow, rounded scallops rather than sharp teeth. Scalloped edges slice rather than saw, so they work well on bread, foam and soft food where a saw tooth would tear the surface. The scallop radius controls how much the material is drawn into the cut. See food processing blade guide.

Also called: wave edge, gull-wing edge

Micro-Serration

Very fine teeth, typically below about 0.5 mm pitch, applied to an otherwise straight edge. Micro-serration improves grip and reduces slip on film and foil while keeping the cut line almost straight, and it is often used on blades that must both cut and hold position.

Also called: fine serration, micro-tooth

Perforation Pattern

The arrangement of holes or interrupted slits along a perforating blade: hole diameter, pitch, number of rows and offset between rows. The pattern has to be fixed before manufacturing because it is cut into the blade, not adjusted afterwards. See perforation patterns.

Also called: hole pattern, perforation layout

Notch Angle

The included angle of a tear notch, usually a V cut into the seal. A narrow angle starts a tear easily but can propagate on its own; a wider angle needs more force to start but tears more controllably. Angle and depth are always specified together.

Also called: tear notch angle, V angle

Razor Edge

An extremely thin, polished edge with a very small included angle, typically under 20 degrees. Razor edges cut with minimal force and are used for film, foil and soft tissue. They are also the most fragile edge type and are unsuitable for any interrupted or abrasive cut.

Also called: fine edge, shaving edge

Hollow Grind

A concave bevel produced by grinding on a large-radius wheel, so the bevel face curves inward. A hollow grind produces a very thin edge with good support behind it, and it reduces friction because only the edge and the top of the bevel contact the material. It also removes less stock at each regrind than a full flat bevel.

Also called: concave grind, radius grind

Relief Angle

The angle between the bevel face and the cut surface, which provides clearance behind the edge. Without relief the blade rubs instead of cutting, which shows up as heat, power draw and a polished wear band on the flank.

Also called: clearance angle, back relief

Rake Angle

The angle at which the cutting face meets the material, measured from perpendicular. A positive rake slices and draws the material in; a negative rake scrapes and is used where the edge has to survive impact. Rake angle is set by the blade holder as much as by the blade.

Also called: cutting angle, hook angle

Clearance

The gap between a blade and its counter-edge, measured horizontally for slitting and radially for shearing. Too little clearance causes rubbing, heat and burrs; too much causes the material to fold into the gap instead of being cut. Clearance is set on the machine but is chosen to suit the blade thickness. See clearance and overlap chart.

See: slitter clearance and overlap

Overlap

The depth by which a slitting disc passes its counter-edge, measured vertically. Overlap has to be enough to complete the cut at the bottom of the disc's runout, but not so much that the discs fight each other. Overlap and clearance are set together and are the usual cause of a slitter that cuts well at low speed and fails at high speed. See overlap settings.

Also called: side overlap, penetration depth

Blade Material and Heat Treatment

Steel grades, carbide classifications and the heat treatments behind them. Grade names differ between standards, so the same material can appear under several designations depending on who supplied the drawing.

Tool Steel

A steel grade formulated to be hardened and to keep a hard edge at working temperature. Most industrial blades are tool steel rather than stainless, because tool steel offers a better balance of hardness, wear resistance and cost. The common families are cold-work (D2, DC53, SKD11), shock-resisting and high-speed. See blade material selection guide.

Also called: tool steel, die steel

D2 Tool Steel

A high-carbon, high-chromium cold-work tool steel, roughly 1.5% carbon and 12% chromium. D2 is the default choice for blades that must resist abrasive wear: granulator knives, slitter discs, shear blades. It holds hardness well but is less tough than DC53, so it is a poor choice where the edge takes heavy impact. See D2 in the material comparison.

Also called: 1.2379, X153CrMoV12, Cr12Mo1V1

DC53

A modified D2 developed to fix D2's main weakness: toughness. DC53 keeps similar wear resistance but resists chipping and cracking much better, which is why it is often preferred for blades that see interrupted cuts or shock loading. It also machines and grinds more easily after heat treatment. See DC53 versus D2.

Also called: DC53 cold-work steel

SKD11

The Japanese standard designation for a cold-work die steel that is broadly equivalent to D2 and Cr12MoV. In practice SKD11 from different mills can vary in cleanliness and carbide distribution, so a brand name alone does not guarantee the same blade life. See SKD11 and its equivalents.

Also called: JIS SKD11, equivalent to D2

Cr12MoV

The Chinese standard cold-work die steel closest to D2 and SKD11. Widely used for domestic blade production because it is available in a range of thicknesses and is cost-effective for large flat parts such as guillotine and sheeter knives.

Also called: Cr12MoV, GB standard die steel

6CrW2Si and 5CrW2Si

Shock-resisting tool steels with moderate carbon and tungsten. They are chosen where the blade has to absorb impact without cracking: chipping knives, shear blades on scrap, and some woodworking knives. Wear resistance is lower than D2 but toughness is significantly higher.

Also called: shock-resisting steel

9CrSi

A low-alloy tool steel with good hardenability and moderate wear resistance, historically common for woodworking knives, paper knives and agricultural blades. It is easier to heat treat than D2 but loses hardness faster at elevated temperature.

Also called: 9CrSi, 9SiCr

Spring Steel

A medium-carbon or silicon-manganese steel such as 65Mn or 60Si2Mn, hardened and tempered to give high elastic strength. Spring steel is used for blades that have to flex without taking a permanent set, and for low-cost razor-type blades. It is not a good choice for sustained abrasive wear.

Also called: 65Mn, 60Si2Mn

High-Speed Steel (HSS)

A tool steel alloyed with tungsten, molybdenum, vanadium and often cobalt so that it keeps its hardness at temperatures that would soften plain tool steel. On blades, HSS is chosen for high-speed or high-temperature cuts, and for thin sections that would be too fragile in carbide. See HSS in the material comparison.

Also called: HSS, highs, 高速钢

M2 High-Speed Steel

The most common general-purpose HSS, roughly 6% tungsten and 5% molybdenum. M2 offers a good balance of hardness, toughness and cost and is widely used for saw blades, drills and cutting knives. It is a sensible default when a blade needs more heat resistance than D2 at similar cost.

Also called: W6Mo5Cr4V2, HS6-5-2

M35 and M42 (Cobalt HSS)

Cobalt-bearing high-speed steels, typically 5% and 8% cobalt respectively. The cobalt raises hot hardness and wear resistance, so these grades hold an edge longer on stainless, abrasive film and high-speed lines. They are harder to grind and more expensive, so they are used where blade life drives the decision.

Also called: cobalt HSS, HS6-5-2-5

420 Stainless Steel

A martensitic stainless steel with about 0.35% carbon and 13% chromium. It can be hardened and offers useful corrosion resistance, which makes it a common choice for food-contact blades, doctor blades and blades washed down in service. Its wear resistance is below D2. See stainless steel blades.

Also called: 420, 1.4021, 2Cr13

420J2 Stainless Steel

A slightly higher-carbon version of 420, giving better hardness and edge retention while keeping the same corrosion class. Frequently specified for doctor blades in printing and coating, and for food processing knives that are cleaned frequently. See stainless doctor blades.

Also called: 420J2, 3Cr13, 1.4028

440C Stainless Steel

A high-carbon martensitic stainless with about 1% carbon and 17% chromium. 440C reaches higher hardness than 420 and resists corrosion better than D2, so it suits blades that need both wear resistance and washdown resistance: food slicers, medical cutters, marine applications. See 440C and 420 stainless grades.

Also called: 440C, 1.4125, 9Cr18Mo

1.4116 Stainless Steel

A German-standard martensitic stainless widely used for food contact knives, with roughly 0.5% carbon, 15% chromium and molybdenum. It balances corrosion resistance against edge retention and is a common specification where food hygiene standards drive material choice. See food contact blade grades.

Also called: X50CrMoV15, 5Cr15MoV

Austenitic Stainless (304 / 316)

Corrosion-resistant stainless grades that cannot be hardened by heat treatment. They are used for blade bodies, guards and food equipment where the part does not form the cutting edge. Specifying 304 for a cutting edge is a common and costly mistake: it will not hold an edge.

Also called: 18-8 stainless, AISI 304/316

Tungsten Carbide

A cemented carbide made by sintering tungsten carbide particles in a cobalt binder. It is far harder and more wear resistant than any steel, which makes it the choice for abrasive stock, but it is also brittle and cannot be sharpened to a fine edge without risk of chipping. See tungsten carbide blades.

Also called: cemented carbide, hard metal, TC

Carbide Grades (YG6, YG8, YG15)

Carbide grade designations describe the cobalt content and grain size. Lower cobalt (YG6) gives higher hardness and wear resistance; higher cobalt (YG15) gives more toughness. The right grade depends on whether the dominant failure mode is wear or impact. See carbide grade selection.

Also called: carbide grade, ISO K/P/M class

Carbide-Tipped Blade

A steel blade body with a carbide insert brazed or mechanically fixed along the cutting edge. This combines a tough, machinable body with a wear-resistant edge, and it allows a large blade to be re-tipped rather than replaced. See carbide-tipped options.

Also called: inserted tooth blade, brazed tip blade

Powder Metallurgy Steel (PM / ASP)

Tool steel produced by atomising the melt into powder and consolidating it, which gives a very uniform carbide distribution with no segregation. PM grades such as ASP23 offer high hardness with much better toughness than conventionally cast equivalents, at a significantly higher cost. See powder steel in the comparison.

Also called: PM steel, particle metallurgy steel, ASP

Hardness (HRC)

Resistance to indentation, measured on the Rockwell C scale for hardened steel. On blades, hardness predicts wear resistance: harder edges last longer on abrasive stock. It does not predict toughness, and past a point extra hardness makes an edge chip rather than wear. See hardness and heat treatment guide.

Also called: Rockwell C, HRC

HRA and HV

Alternative hardness scales. HRA is used for cemented carbide because HRC is not reliable above roughly 68 HRC. HV (Vickers) is a laboratory scale used for case depth, coating hardness and very thin sections. When comparing suppliers, confirm which scale a number refers to.

Also called: Rockwell A, Vickers

Heat Treatment

The controlled heating, quenching and tempering cycle that turns a soft steel blank into a hardened blade. Hardness alone is not the goal: the tempering step sets the balance between wear resistance and toughness, and it is usually the step where a cheap blade differs from a good one. See heat treatment explained.

Also called: hardening, HT

Quenching and Tempering

Quenching cools the steel fast enough to form martensite, which is very hard and very brittle. Tempering reheats it to a lower temperature to relieve stress and restore toughness, trading a little hardness for a lot of durability. The tempering temperature is chosen for the application, not for maximum hardness.

Also called: Q&T, hardening and drawing

Cryogenic Treatment

Cooling a hardened blade to around minus 80 to minus 190 degrees Celsius before tempering, to convert retained austenite into martensite and relieve residual stress. It can improve dimensional stability and, on some grades, wear life. It does not rescue a badly heat-treated blade, and the gain varies by grade and application. See cryogenic treatment: what it does.

Also called: deep cryo, sub-zero treatment

Annealing

A softening heat treatment applied before machining or grinding, so the steel can be cut and shaped without cracking. Blades are annealed in the blank state and hardened only after the profile and holes are finished, because hardening distorts the part.

Also called: soft annealing, spheroidise annealing

Nitriding

A surface treatment that diffuses nitrogen into the steel to create a hard, wear-resistant case without quenching. On blades it is used for wear surfaces and for parts that must not distort. The case is thin, so it does not survive repeated regrinding.

Also called: nitrocarburising, gas nitriding

Blade Coating

A thin surface layer applied to reduce friction or increase wear resistance: TiN, TiAlN, CrN, DLC and ceramic variants. Coatings help most where the failure mode is adhesion or rubbing, such as sticky film or wet ink. They do not compensate for an unsuitable base steel or a bad edge geometry. See industrial blade coatings.

Also called: PVD coating, surface treatment

Hardness versus Toughness

The central trade-off in blade specification. Hardness resists wear; toughness resists chipping and cracking. Every material and heat treatment choice moves along this line. High-speed or abrasive cuts push towards hardness, interrupted or impact cuts push towards toughness, and most blade failures come from choosing the wrong end. See choosing the best material.

Also called: wear resistance vs impact resistance

Hardenability

How deep a steel can be hardened, which depends on alloy content rather than on carbon alone. Poor hardenability shows up as a soft core under a hard skin, and on a thick blade it means the edge and the body behave differently after grinding.

Also called: through-hardening depth

Dimensions, Tolerance and Inspection

How a blade is measured and what the numbers actually control. Most interchangeability problems on replacement blades trace back to one of these features rather than to the edge.

Outside Diameter (OD)

The overall diameter of a circular blade. OD sets the surface speed at a given rpm, so it must match the machine's designed rim speed. It also determines how much the blade can be reground before it drops below the usable range. See circular blade size chart.

Also called: outer diameter, disc diameter

Inside Diameter (ID) and Bore

The central hole that mounts the blade on its shaft or hub. Bore diameter, its tolerance and the fit class matter: a loose bore lets the blade run eccentric, which shows up as an uneven slit width and vibration. See standard bore sizes.

Also called: bore, centre hole

Keyway

A slot cut into the bore to take a drive key, transmitting torque from the shaft to the blade. Keyway width, depth and position are usually matched to a standard, and a mismatch is a common reason a correctly sized blade will not mount.

Also called: key slot, drive slot

Mounting Hole Pattern

The arrangement of bolt holes used to clamp a blade to its holder, described by hole diameter, count and pitch circle diameter. On packaging and granulator blades this pattern is often the single feature that decides whether a blade is interchangeable with the OEM part. See hole patterns to OEM drawings.

Also called: bolt pattern, hole layout, PCD

Slot

An elongated hole that allows adjustment or accommodates thermal expansion. Slots give a blade some setting range on the machine, but they also reduce the clamped area, so slot width and end radius have to be right or the blade will crack from the corner.

Also called: slotted hole, elongated hole

Blade Thickness

The body thickness behind the bevel. Thickness controls stiffness and how much the blade deflects under cutting load. A blade that is too thin for its diameter will chatter and produce a wavy cut; too thick wastes material at each regrind.

Also called: gauge, plate thickness

Blade Length and Width

The overall dimensions of a straight blade. For guillotine and sheeter knives, length tolerance across the full span matters more than the nominal number, because the whole edge engages the stack at once. See guillotine blade dimensions.

Also called: overall length, span

Tolerance

The permitted deviation from a nominal dimension. On blades, tolerance is quoted per feature: diameter, thickness, bore, hole position, flatness. A single headline tolerance figure is meaningless without saying which feature it applies to.

Also called: dimensional tolerance, deviation

Flatness

How closely a blade face approaches a true plane. Flatness is critical on doctor blades and guillotine knives, where any deviation shows up as an uneven film or an incomplete cut across the width. It is measured on a surface plate or with a laser. See doctor blade flatness requirements.

Also called: planarity, face flatness

Parallelism

How closely two faces stay the same distance apart across the part. A blade can be flat but not parallel, which produces a wedge-shaped cut or an uneven clamp load. Parallelism is the key tolerance on doctor blades and slitter discs.

Also called: thickness variation, taper

Perpendicularity

How close an edge or face is to a true right angle with a reference surface. On a guillotine blade, a non-perpendicular end means the cut is out of square even when the edge is sharp.

Also called: squareness

Runout

The total movement of a rotating blade's edge as it turns, measured with a dial indicator. Runout combines the blade's own eccentricity, its bore fit and the machine spindle. High runout causes an intermittent cut, which is often misdiagnosed as a dull blade.

Also called: TIR, total indicated runout

Concentricity

How closely the bore and the outer edge share a common centre. A blade with good concentricity runs true even at high rpm; a poorly concentric blade cannot be corrected by balancing.

Also called: eccentricity, co-axiality

Surface Finish (Ra)

The roughness of a machined face, expressed as Ra in micrometres. On a doctor blade the face finish affects how evenly the metered film releases; on a slitter the bore finish affects fit and fretting. Roughness is separate from flatness and both have to be specified.

Also called: roughness, Ra value

Burr

A raised lip of deformed material left along an edge after grinding or cutting. On a blade, burr is a defect: it changes the effective edge angle, causes tracking errors on a web and can transfer marks to the product. Deburring is a finishing step, not an optional one. See burrs on slitting lines.

Also called: wire edge, raised edge

Chamfer

A bevelled corner added to break a sharp edge for handling safety or to guide assembly. Chamfers on mounting holes and blade corners are cosmetic in appearance but functional in service, since an unbroken corner is where cracks start.

Also called: edge break, bevel corner

Counterbore and Countersink

Recesses machined around a hole to let a socket-head or flat-head fastener sit below the surface. On blades, the counterbore depth has to suit the screw head or the clamp load will be carried by the screw instead of the blade.

Also called: spotface, c'bore, c'sink

Bevel Direction

Which face of the blade carries the grind, and which way it faces in the machine. Getting this wrong produces a blade that fits but cuts badly or rubs, and it is one of the most common errors when a replacement is ordered from a drawing alone. See bevel direction on replacement blades.

Also called: grind side, edge orientation

Rockwell Testing

The standard shop-floor hardness check, made with a diamond indenter at a defined load. Hardness is normally verified on a sample or on a non-critical area of the part, and a single reading says little: consistency across a batch is what indicates a controlled heat treatment. See how hardness is verified.

Also called: HRC test, hardness check

Dimensional Inspection

Verification of a finished blade against its drawing: dimensions, hole positions, flatness and edge condition. For a repeat or OEM-replacement order, the inspection record is what makes the next batch identical to the first.

Also called: QC inspection, first article inspection

First Article Inspection (FAI)

A full dimensional and visual check of the first blade from a new or changed process, documented against the drawing. FAI is the point where a sample becomes a repeatable product, and it is the document to ask for when qualifying a new supplier.

Also called: FAI, first-off inspection

Surface Plate Measurement

Checking flatness and parallelism by resting the blade on a calibrated plate and measuring the gap or indicator movement. Simple, fast and adequate for most blade work, which is why it remains standard practice alongside CMM inspection.

Also called: plate check, bench inspection

Wear, Failure and Troubleshooting

The failure vocabulary. Being able to name the failure mode is what separates a blade that needs replacing from a machine that needs adjusting.

Edge Wear

Progressive loss of material from the cutting edge, which shows first as a polished band along the flank. Wear is normal and predictable; the useful question is the rate, because a blade that wears twice as fast usually indicates the wrong grade rather than a defective blade. See extending blade service life.

Also called: flank wear, wear land

Chipping

Small pieces breaking out of the cutting edge. Chipping is a toughness failure, not a wear failure, so the fix is a tougher grade, a larger included angle or a micro-bevel, rather than a harder steel. Impact, hard inclusions and an unstable holder are the usual causes. See blade troubleshooting guide.

Also called: nicking, edge breakout

Cracking

A fracture running into the blade body from the edge or from a hole. Cracks start where stress concentrates: hole edges, slot ends, sharp corners and heat-affected zones from laser cutting. Once visible, the blade is scrap. See crack diagnosis.

Also called: fracture, fissure

Thermal Cracking

A network of fine cracks caused by repeated rapid heating and cooling of the edge, typical of high-speed dry cutting. The cure is cooling, speed reduction or a grade with better hot hardness, not more frequent sharpening.

Also called: heat checking, craze cracking

Fatigue Failure

Failure after many cycles of load rather than one overload, starting as a small crack at a stress raiser and growing until the blade breaks. On blades, fatigue is common where clamping is uneven or where a blade runs with excessive runout.

Also called: fatigue cracking, cyclic failure

Edge Rollover

Plastic deformation of the cutting edge, where the tip bends over instead of wearing away. Rollover means the steel is too soft for the load, or the clearance is so small that the edge is being hammered rather than cutting.

Also called: edge deformation, mushrooming

Galling

Material transferring from the workpiece onto the blade face through pressure and friction. Galling raises friction, increases cutting force and eventually tears the edge. Sticky film, soft aluminium and wet ink are the usual triggers, and a coating or a smoother face is the usual fix. See coatings against galling.

Also called: pick-up, smearing, built-up edge

Corrosion

Chemical attack on the blade, appearing as staining, pitting or a dulled edge. In food, printing and washdown environments corrosion is often the real cause of short blade life, and the answer is a stainless grade rather than a harder tool steel. See corrosion-resistant blade grades.

Also called: rust, oxidation, pitting

Uneven Wear

Wear that is heavier at one end or one side of the blade. Uneven wear almost always indicates a machine problem: a non-parallel jaw, a bowed holder, or material tracking to one side. Replacing the blade without correcting the cause reproduces the same pattern. See diagnosing uneven wear.

Also called: tapered wear, one-sided wear

Misalignment

A blade that is not square, parallel or concentric with its reference. Misalignment shows up as a stepped cut, a wavy edge, vibration or accelerated wear on one flank, and it is usually the first thing to check before blaming the blade. See alignment checks.

Also called: out of alignment, skew

Over-Clamping

Clamping a blade harder than its design allows, which bows the blade and distorts the edge line. On doctor blades it produces a heavier film at the ends than in the middle; on slitters it causes the disc to cone. More clamp pressure is rarely the fix for a poor cut. See doctor blade clamp pressure.

Also called: over-tightening, excess clamp load

Incorrect Clearance

A slitter or shear set with too much or too little gap between the blades. Too little gives rubbing, heat and burrs; too much gives a folded or torn edge. Clearance is a machine setting but has to be chosen to suit the blade thickness and material. See setting clearance correctly.

Also called: wrong gap, bad clearance

Regrinding

Re-sharpening a worn blade by grinding a new bevel. Regrinding is economical up to a point, but each pass removes body thickness and changes the relationship between the edge and the holder. A blade reground past its limit will no longer fit or hold its setting. See when to regrind and when to replace.

Also called: resharpening, re-sharp, sharpening

Minimum Regrind Thickness

The thinnest a blade can be before it stops working. Once a blade approaches this limit, further grinding saves nothing because the blade will deflect, sit differently in the holder or fail to reach the anvil. Recording starting thickness is the only way to manage this.

Also called: wear limit, scrap thickness

Blade Life

The useful cutting time between sharpenings or replacements, expressed in running hours, tonnes, metres or packs. Blade life is only comparable between suppliers if the material, speed and acceptance criterion are the same. A quoted life figure without those conditions means very little. See measuring blade life.

Also called: tool life, service life

Break-In Period

The first part of a blade's life, during which a new edge settles into its wear pattern. Some blades cut slightly differently in the first hours than later, which is why a new blade should be judged over a full run rather than a single sample.

Also called: running-in, settling

Frequently Asked Questions

What is the difference between a blade and a knife in this industry?
In practice, nothing. Blade and knife are used interchangeably for the same part; the word tends to follow the machine rather than the geometry. A packaging line uses blades, a granulator uses knives, and both describe the same kind of hardened steel cutting part. We use whichever term the buyer uses.
How do I know which blade type my machine needs?
Start from the station, not from the blade: what is the blade doing at that point in the process, what material is it cutting, and what does the holder look like. A photo of the worn blade with a ruler in frame, plus the machine model, is usually enough to identify the type and the critical dimensions.
Is a harder blade always a better blade?
No. Hardness buys wear resistance and costs toughness. A blade that is too hard for its application chips instead of wearing, which shortens life and can damage the product. The right hardness is the one that matches the dominant failure mode: abrasive wear pushes hardness up, impact and interrupted cuts push it down.
What do the terms single bevel and double bevel mean for ordering?
Single bevel means the blade is ground on one face only, leaving a flat back; double bevel means both faces are ground to a central edge. This matters because a single-bevel blade can only be mounted one way, and ordering the wrong one produces a blade that fits but does not cut correctly.
Why does the same blade last much longer on one machine than another?
Blade life depends on the machine as much as on the blade: clamp pressure, alignment, clearance, runout and material variation all move the wear rate. Before changing the steel grade, check that the holder is square, the clearance is correct for the material, and the blade is not being over-clamped.
Can you make a blade from a worn sample instead of a drawing?
Yes, and for older or imported machines a worn sample is often the most reliable input. We measure the outline, hole pattern, thickness and remaining bevel, then confirm the critical dimensions with you before production. Where the worn edge no longer represents the original geometry, we ask for the machine model as a cross-check.
What information should I send with a blade enquiry?
The machine make and model, what the blade cuts, the material of the blade if known, the dimensions you can measure, and a photo with a scale. If the blade carries an OEM part number, include it. That set of inputs is enough for a first technical response without any back-and-forth.
Do blade terms differ between countries?
Yes, and that causes real ordering errors. The same steel can be called D2, SKD11, 1.2379 or Cr12MoV depending on the standard; the same slitter can be called a top knife, a male knife or an upper disc. When a specification is ambiguous, we confirm the standard or ask for the drawing rather than guess.

Not sure which term applies to your blade? Send a photo with a ruler in frame, the machine model, and any numbers stamped on the blade. We will identify the type and the critical dimensions before quoting.

Send the details

Related: blade materials and grades · circular blade size chart · custom blade manufacturing · packaging machine blades · serrated knives · doctor blades · granulator blades · distributor partnership