Industrial Blade Supply for Distributors, OEMs and Spare Parts Partners

We supply blades to companies that resell them, fit them into machines, or keep them in stock for their own customers. The work is less about a single order and more about a specification that holds, order after order.

  • 4Partner
    types
  • 6Supply
    requirements
  • 6Blade
    groups
  • 5First-order
    steps

Partnership

We supply industrial blades to companies that resell them, fit them into machines, or keep them in stock for their own customers. The work is less about a single order and more about a specification that holds: the same drawing, the same material, the same edge, order after order.

This page sets out who we work with, what a supply relationship actually requires on both sides, and how a first order usually starts.

Dekeer · blade manufacturing · updated November 2026

Who We Work With

Four kinds of partner, with different reasons for buying. The common thread is that each one sells or fits a part they did not design, so the specification has to be explicit.

Distributors and wholesalers

Companies holding stock and reselling industrial consumables into their own region. What matters here is that a repeat order is the same blade as the first one, with the critical dimensions held from batch to batch.

Typical requirement: Repeatable specifications and documented dimensions

Machine builders and OEMs

Builders who fit blades into new machines and need a replacement channel afterwards. The blade becomes part of the machine specification, so the drawing and the approval process matter more than the price of a single part.

Typical requirement: Drawing-controlled supply matched to the build

Service and spare parts companies

Businesses that maintain packaging, converting, recycling or food equipment and supply wear parts to their own customers. They usually work from a worn sample rather than a drawing, and need a fast technical answer before they commit.

Typical requirement: Identification from a worn sample or OEM number

Online and catalogue sellers

Sellers listing blades in their own catalogue or marketplace. Here the requirement is often neutral packing, stable product data and an edge profile that a photo can convey accurately.

Typical requirement: Neutral packing and consistent product data

What a Supply Relationship Actually Needs

Distributor conversations tend to start with a part and a question about price. The parts that go wrong later are almost never about price — they are about a specification that was never written down. These are the six things we treat as the substance of the relationship.

  • A specification that survives a repeat order — Every blade we supply against is defined by a working drawing that records material, hardness, edge geometry and the critical dimensions. The drawing, not a photograph, is what makes the fifth order identical to the first.
  • Batch consistency on the features that matter — Hardness, thickness, hole pattern and bevel are the four things that change how a blade seats and cuts. We control those against the drawing and inspect by sample, so a delivery does not surprise the person fitting it.
  • OEM replacement matching — Where a customer is replacing a branded machine part, we work from the OEM part number, a worn sample, or the machine model, then confirm the critical features before production. Where a number is obsolete, the sample is the fallback.
  • A clear path from sample to volume — The usual route is a trial that proves the specification before any repeat commitment. From there the drawing stays fixed and reorders are produced against it.
  • Technical response on drawings, not a price list — Drawings and worn samples are read by the same team that sets production. If a dimension on your drawing cannot be held, we say so before manufacturing rather than after delivery.
  • Packing and labelling that fit your channel — Blades can be supplied in neutral or your own branded packing, with or without individual marking, so the part reaches your customer without revealing the upstream source.

Blade Range Available for Resale

The categories most often supplied through distribution partners. Each links to the technical detail for that blade family.

Anything outside these families is handled as a custom item — the same drawing and approval process applies, and the geometry is confirmed from a sample or drawing rather than from a catalogue listing.

How a Supply Relationship Starts

Five steps, and the third one is where most sourcing problems are prevented.

  1. Send the part, sample or drawing — A worn blade with a ruler in frame, a dimensioned drawing, an OEM part number, or the machine model. Any one of these is enough to start; more than one is better.
  2. Technical review and open questions — We check the critical features, flag anything that cannot be held, and come back with a specification to approve rather than a bare quotation.
  3. Approve the specification — Material, hardness, edge geometry and the tolerances that matter are confirmed in writing before anything is cut. This is the step that makes repeat orders possible.
  4. Trial production and inspection — The first blades are produced to the approved drawing and inspected on the recorded dimensions. You receive the parts plus the inspection figures.
  5. Fix the drawing and repeat — Once the trial is accepted the drawing is fixed. Reorders, including orders placed by your own customers through you, are produced against that same revision.

From the outside this looks slower than sending a photo and receiving a number. In practice it removes the loop where a first delivery arrives, does not fit, and has to be made again — which costs more time than the approval step ever does.

What to Send First

Best: a dimensioned drawing

Outline, thickness, hole positions, bevel direction and the tolerances that matter. If the drawing came from a previous supplier, that is fine — we will confirm it rather than copy it blindly.

Good: a worn sample

Photographed flat with a steel rule in frame, plus the machine make and model. The worn edge tells us the bevel family; the body tells us the dimensions.

Also good: an OEM part number

Useful on its own for common machine brands, and stronger when combined with the machine model. If the number is obsolete we confirm by geometry instead.

Helpful in every case

What the blade cuts, how it currently fails (wears, chips, or the pack does not open), and whether it sees moisture or food contact. Those three answers usually decide the material.

Questions Distributors Ask

Do you supply under our own brand?
Yes. Blades can be supplied in neutral packing or in packing carrying your own brand, with or without product marking. This is common for distributors and catalogue sellers who need the part to reach the end user under their own name.
Can you work from a worn sample instead of a drawing?
In most cases yes, and for imported or discontinued machines it is often the only available input. We measure the outline, thickness, hole pattern and remaining bevel, and where the worn edge no longer represents the original geometry we ask for the machine model as a cross-check.
How do you handle an OEM part number that is no longer produced?
We confirm the part by its geometry rather than by the number: outline, hole positions, thickness and bevel direction. If those match, the number being obsolete does not prevent supply. If they do not match, we say so before quoting.
What do you need to quote a replacement blade?
A photo with a scale, the machine make and model, the dimensions you can measure, the material if it is known, and any number stamped on the part. For repeat items, an existing drawing from a previous order is the fastest route.
Can you hold a fixed specification across future orders?
Yes, and that is the point of the approval drawing. Once a drawing is agreed it becomes the reference for that part, so reorders are produced to the same revision rather than re-interpreted from a fresh sample each time.
Do you supply to distributors outside your existing markets?
We work with partners in Europe, the Middle East, Southeast Asia and the Americas. The practical starting point is a specific part rather than a catalogue request: send one item you already sell and we can establish whether the specification and the supply route fit.
Can you support a customer's own drawing with tolerances we set?
Yes, within what the process can hold. Where a requested tolerance is tighter than the blade needs, we will say so and explain what it would cost in process time — a blade does not become better because a number on the drawing has more decimal places.

Start with one part you already sell. Send the drawing, a worn sample or the machine model, and we will come back with a specification you can approve rather than a number you have to trust.

Talk to us about supply

Related: blade terminology · blade materials guide · custom blade manufacturing · blade size chart · product series