Custom blade manufacturing

Custom Cutting Blades Made to Your Drawing

Send a drawing, a worn sample, or a photo with dimensions. We forge, machine and grind the blade to match it — from a single trial piece to a scheduled production run.

  • In-house productionForging, heat treatment and CNC grinding under one roof
  • HSS · D2 · 440C · CarbideMaterial selected against what the edge has to survive
  • Drawing, sample or photoAny of the three is enough for a first quotation
01 — Getting started

You do not need a finished drawing to start

Most custom blade enquiries begin with something incomplete: a sketch with three dimensions filled in, a broken blade in a plastic bag, or a photo taken on a phone next to a ruler. Any of those is enough for us to quote. We will tell you which dimensions are missing and why each one matters before any tooling is touched.

01

A drawing

PDF, DWG or DXF. Outline, thickness, edge angle, hole pattern and any tolerance callouts you already work to.

02

A worn blade

Post the used part. We measure it, work back to the original geometry and confirm the profile with you before machining.

03

A photo and sizes

Length, width, thickness, edge angle and hole positions written on a sketch is usually enough for a first quote.

04

A machine and part number

Tell us the machine make and model, or the part number stamped on the blade, and we will identify what fits.

02 — Range

What we make

Twenty years of custom blade work has concentrated on a handful of blade families. Each one below has its own page covering materials, edge geometry and the applications it serves.

03 — Process

How an order runs

  1. Specification review

    We go through what you sent, list the dimensions that are missing, and confirm how the blade mounts and what it cuts. If something on the drawing will not work in service, we say so at this stage rather than after delivery.

  2. Quote and proposal

    You receive the price, the material we recommend and why, the lead time, and the packing method. If a standard profile in our range already fits, we will tell you that too — a cheaper answer is still a good answer.

  3. Trial piece

    For a new profile we produce one piece or a small trial batch first, so the geometry can be proven on your machine before a production quantity is committed.

  4. Production

    Forging or blanking, heat treatment to the specification agreed for the material, CNC grinding of the profile, then edge finishing and, where specified, coating.

  5. Inspection and dispatch

    Every batch is checked against the drawing before packing. We arrange export packing, the documents your customs broker needs, and shipping to your address or your forwarder.

04 — Materials

Materials and edge finishes

Material choice is driven by what the edge has to survive. A blade cutting hot sealing film at 200 °C and a blade granulating glass-filled nylon do not want the same steel, and picking the wrong one shows up as short life rather than as a broken part.

  • High speed steelThe default for toothed cutters and shearing edges that must stay sharp through impact.
  • D2 / SKD11 cold work steelHigh wear resistance for long runs on abrasive stock.
  • 420 / 440C stainlessFood contact, wet environments and washdown areas.
  • Solid tungsten carbideFor the cases where steel simply wears out too fast, at the cost of brittleness.
  • CoatingsTiN, TiCN and DLC applied where friction or chemical attack is the limiting factor.

Heat treatment is carried out to a written specification for the grade, and hardness is checked on samples from each batch.

05 — Quotation

What to include when you ask for a price

The faster these five points arrive, the faster a usable number comes back:

  • Dimensions, a drawing, or a sample we can measure
  • Quantity for the trial and the expected repeat quantity per year
  • Material, if you already specify one, or the application so we can recommend
  • Machine make and model, or the part number of the blade being replaced
  • Delivery destination and the terms you buy on

We work with drawings under NDA where that is required, and we do not reuse a customer’s profile for anyone else.

06 — Questions

Questions we are asked before a first order

Can you work from a sample instead of a drawing?

Yes. Send the worn or broken blade and we will measure it, reconstruct the geometry and send the profile back to you for confirmation. This is common where the original drawing was never released by the machine builder.

What is the smallest quantity you will run?

We accept trial orders in small quantities so a new profile can be tested on your machine before a production batch is placed. Tell us the trial quantity you need and we will quote against it rather than against a fixed minimum.

How long does a custom blade take?

It depends on whether the profile is new or a repeat. A repeat of a blade we have made before is quoted against stock material; a new profile needs drawing review, tooling and a trial piece first. We give a dated lead time with the quote and tell you which stage is the long pole.

Can you match a part number from our machine supplier?

Send the number and, if possible, the machine model. We can confirm whether the geometry is something we already produce or whether it needs to be made from your drawing or sample.

Do you sign an NDA?

Yes. Drawings and samples sent under an NDA stay with the people who need them to make the part, and the profile is not offered to other customers.

Can you ship to our own forwarder?

Yes. We can ship to your address directly or hand the goods to a forwarder you nominate, with the export documents prepared for whichever route you use.

Next step

Send the drawing, get a real answer

Tell us what the blade has to do and what it has to fit. You will get a quote with a material recommendation and a dated lead time, not a request for more information.

  • PDF, DWG or DXF drawings — a worn sample works too
  • NDA signed before anything leaves your side
  • One quote covering material, tooling and lead time

Prefer email? dkeblade@163.com — drawings can go in the same thread.

Request a quote

Name, email and one line about the blade is enough to start.

After you send the form we reply by email, and the drawing can be attached in that thread.